SET-UP AND ASSEMBLY Mower Assembly Kit in Crate / Parts Box Parts in Burlap Bag Parts in Parts Box 9
SET-UP AND ASSEMBLY Pre-Delivery Check List (Dealer Responsibility) 1. Inspect the mower thoroughly after assembly to ensure it is set up properly bef
SET-UP AND ASSEMBLY MOUNTING MOWER LIFT SYSTEM Install with the tractor on level ground. Lock the parking brake, set the transmission lever in "N
SET-UP AND ASSEMBLY Lift Link\ Lower Link Shaft Y- bracket Attaching Lift Link to Lift Plate Assembly (For Tractors Without Rear Three Point Hitch) 1.
SET-UP AND ASSEMBLY Installing Lift Rods (For Tractors Without Rear Three Point Hitch) 1. Adjust the lift rod to 365 mm (14.4 in) measured from eye t
SET-UP AND ASSEMBLY I I I I ‘y 85 mm 7 3.4 in. (with loader subframe) 100mm ; 4.0 in. -y Installing Lift Rods on Lower Link Lift (For Tractors With a
SET-UP AND ASSEMBLY Adjusting Lift Rod (For Tractors With and Without Rear Three Point Hitch) Follow this procedure if you do not have a loader subfra
SET-UP AND ASSEMBLY Subassembling Front Link Brackets Assemble by compressing the front spring and inserting it in the front bracket slot. Pass grease
INSTALLING MOWER ASSEMBLING MOWER Checking Rear Mower Deck Links Rear mower links will come installed. Check that vibration in shipping has not shaken
INSTALLING MOWER < \ Front Caster Wheel Rear Gauge Wheels \'@ Installing and Adjusting Wheels 1. Pull release pin on wheel yoke so that wheel
INTRODUCTION TO THE OWNER Read this manual before operating your mower. The information presented will prepare you to do a better and safer job, Keep
INSTALLING MOWER NOTE: Tool is available (see illustration) for ease of measurement. 1. To level mower from side to side, measure distance from front
INSTALLING MOWER Installing Discharge Chute Cover 1. Using 3/8 x 1 in. carriage bolts, insert bolts from under mower deck, passing through hol
INSTALLING MOWER Attaching Front Mower Links To Mower 1. Screw the adjustable plate link onto the right and left front mower links. Adjust the plate l
~~ INSTALLING MOWER Rear Mower Links Attach to Mower 4. Put the transmission range selector in "1." For A-4 models, engage 4-wheel drive. Pr
INSTALLING MOWER Attaching Front Mower Links to Front Bracket 1. Pull back on quick release pin in right or left front link bracket and twist until th
INSTALLING MOWER Lift Arms Fasten to Mower Deck LOADER 0.2in SUB FRAME MOWER DECK STOP 24 Fastening Lift Arms to Mower Deck 1. Screw the eye bolt into
INSTALLING MOWER DETACHING MOWER FROM TRACTOR I Detaching Front Links NOTE: If mower deck hook is engaged to hold mower deck up, deck must be raised a
INSTALLING MOWER U-Joint Detaches From Mid-PTO Detaching Mid-PTO and Mower Drive Shaft 1.With engine off, PTO selector set to "REAR" and key
INSTALLING MOWER Moving Tractor Off Mower 1. Before detaching, chock front and rear wheels of mower as illustrated. Place triangular piece of wood in
OPERATION Safety is a primary concern in the design and manufacture of our products. Unfortu- nately, our efforts to provide safe equipment can be wip
INTRODUCTION GENERAL INFORMATlON The purpose of this manual is to assist the opera- tor in maintaining and operating this mower. Read it carefully. It
OPERATION ADJUSTING CUTTING HEIGHT Mower cutting height is raised, lowered, and maintained by adjusting caster and gauge wheels. Refer to figure and a
OPERATION PRE-OPERATION CHECK LIST Operate tractor mid-PTO at no more than 2400 RPM (maximum governed engine RPM). You may not be able to stop the tra
OPERATION OPERATING TECHNIQUE Proper ground speed will depend upon the terrain, the height, type and density of material to be cut. Normally, ground s
OPERATION Small Area Cuffing Pattern t Large Area Cutting Pattern CUTTING PATTERNS These cutting patterns are only recommended for a flat, level lawn
INSTALLING MOWER OPERATING YOUR MOWER WITH OTHER EQUIPMENT You may operate your MM60 mower with three- point hitch mounted attachments and with the FL
INSTALLING MOWER 4. Place other attachment on Rear Three Point by mower deck hook. Hitch . Mower deck will be held out of the way NOTE: The mower deck
INSTALLING MOWER Using Rear Three Point Hitch with Mower Detached While the Mower Lift Linkage is Still Installed 1. Detach mower as described below.
MAINTENANCE OWNER SERVICE The information in this section is written for opera- tors who possess basic mechanical skills. Should you need help, your d
MAINTENANCE LUBRICATION INFORMATION Do not let excess grease collect on or around parts, particularly when operating in sandy areas. The accompanying
MAINTENANCE BLADE INSPECTION Before each use, check each mower blade for damage or abnormal wear. . NORMAL EXCESSIVELY WORN -= CRACKED Blade Condition
CONTENTS INTRODUCTION 1 TO THE OWNER ...
MAINTENANCE ~~ BLADE SERVICING Inspect blades for condition and proper installa- tion each time before operation. Replace any blade that is bent, exce
MAINTENANCE !a. Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangero
MAINTENANCE REPLACING BLADE BELT Removing Blade Belt 1. Remove right and left pulley covers (as viewed from rear of mower). Right cover is held on by
MAINTENANCE DEALER LEVEL MAINTENANCE The information in this section is written for dealer service personnel. The repair described herein requires spe
MAINTENANCE SPINDLE REPAIR Blade Spindle Removal 1. Remove blade from spindle. (See Blade Re- moval on Page 39.) 2. Remove belt shield. 3. Remove belt
MAINTENANCE-.. —1 1. Spindle assembly 2. Seal 3. Sleeve 4. Bearing cone 5. Housing and cups 6. Cup 7. Shaft Spindle Assembly Blade Spindle Disassembly
MAINTENANCE Blade Spindle Assembly 1. Bearing cups and cones are designed to work together. It is important to position them so bearing cone taper mat
MAINTENANCEt1 I 1. Spindle assembly 2. Seal 3. Sleeve 4. Bearing cone 5. Housing and cups 6. Cup 7. Shaft Spindle Assembly 10. Apply a thin coat of lu
MAINTENANCE 6 UNIVERSAL JOINT REPAIR 1. Yoke 2. Journal cross m5 3. Seal 4. Snap ring 5. Cup and bearings 6. Yoke Universal Joint Assembly Disassembly
MAINTENANCE h ... L 11' 3. Clamp cup in vise as shown and tap on yoke to completely remove cup from yoke. Repeat steps two and three for opposite
SAFETY INFORMATION Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can
MAINTENANCE GEARBOX MAINTENANCE Read this complete section before starting any repair. Many steps are dependent on each other. 1. Gearbox bearings, ge
MAINTENANCE Seal Seal\ e- Vent Plug al Gearbox gasket 1 Gear Box Leakage Repair 1. Bore-tite™, a sealant, is used on the outer diameter of the seals.
MAINTENANCE Drive Pulley Installation 1. Install drive pulley with split taper bushing on gearbox vertical shaft. Make sure key and keyways are aligne
STORAGE STORAGE 1. Remove the mower deck from the tractor. 2. Turn the mower deck upside down. Clean the underside of the deck with water, and dry tho
TROUBLESHOOTING PROBLEM SOLUTION 1. Mower overloading; material too tall or heavy 1. Reduce tractor speed but operate Mid-PTO at 2400 rpm. Cut ma
TROUBLESHOOTING PROBLEM SOLUTION ~~~ ~~~ 1. Tractor speed too fast 1. Shift to lower gear. 2. Grass accumulation inside deck 2. Clean deck underside.
SPECIFICATIONS Overall length 1345 mm (53.8") Overall width 1820 mm (72.8") Mowing width 1500 mm (60") Weight (including linkage) 140
WARRANTY SERVICE OWNER SATISFACTION Your satisfaction and goodwill are important to your dealer and to us. All HONOA warranty details are explained in
Current customer service contact information: United States, Puerto Rico, and U.S. Virgin Islands: Honda Power Equipment dealership personnel are tra
SAFETY INFORMATION Preparation Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work s
SAFETY INFORMATION Stop mower and tractor immediately upon striking an obstruction. Turn off engine, remove key, inspect and repair any damage before
SAFETY INFORMATION Safety Decals Replace immediately if damaged. IMPORTANT FILL GEAR BOX TO CENTER LINE OF HORIZONTAL SHAFT. USE SAE 90 GEAR LUBE. A
SET-UP AND ASSEMBLY DEALER SET-UP INSTRUCTIONS Assembly of this mower is the responsibility of the dealer. The mower should be delivered to the owner
Kommentare zu diesen Handbüchern